Get a Quote
NOx reduction technologies for gas turbines

NOx reduction technologies for gas turbines

Aug 10, 2017 There are several available technologies for reducing the NOx gas generation during the combustion. They include (1) injection of water or steam in the combustion zone to lower the flame ...

More details
water injection in gas turbines - Heat Transfer ... - Eng-Tips

water injection in gas turbines - Heat Transfer ... - Eng-Tips

Aug 21, 2005 Water injection for NOx control in modern industrial type GT's is used with liquid fuel. When using GAS only as fuel, most manufacturers developed the DRY NOx control. WET NOx control (with water or steam injection) has a limitation in the amount of NOx abatement attainable, compatible with flame stability (about 42 ppm).

More details
NOx control - Marine Inbox

NOx control - Marine Inbox

Aug 29, 2019 In water emulsion, fuel is mixed with water in water injection a separate fresh water injector is mounted in the cylinder head which injects water. This method has a drawback of increasing the specific fuel oil combustion with reduction in NOx by only 20-45%., thermal efficiency reduces, corrosion problems. 4. Combustion air treatment

More details
Power Plant NOx Reduction - SCR vs SNCR Technology

Power Plant NOx Reduction - SCR vs SNCR Technology

Dec 20, 2018 The basic chemical principle is that at a high temperature, ammonia or urea reacts with NOx from the combustion gases to yield nitrogen gas (N 2) and water vapor (H 2 O). SNCR can be used to reduce NOx by about 30 – 70 %. Below are simplified equations of the reaction using ammonia as the reagent: 4 NO + 4 NH₃ + O₂ → 4 N₂ + 6 H₂O (Eq.

More details
Water Injection System to Reduce NOX Emissions

Water Injection System to Reduce NOX Emissions

Jan 01, 2010 The injected water lowers the peak flame temperature in the engine, decreasing NO X emissions. As a result, the combustion turbine units with HP water injection facilitate compliance with current...

More details
POLITECNICO DI TORINO

POLITECNICO DI TORINO

modified by a water injection implementation which allow to study the effect of water for NOx emission reduction. Since the computational effort on describing the water injection spray using Volume of Fluid (VOF) approach is very computationally demanding, a simple approach which consider water injection like a simple heat sink is proposed. In ...

More details
Water in Diesel Combustion

Water in Diesel Combustion

Optimized direct water injection systems for NOx control show water consumption levels that are comparable to those seen in emulsions. Figure 6 shows NOx reduction at different water consumption (and different fuel and water nozzle configurations) as measured on a large, two-stroke marine diesel engine [603]. The fuel consumption was not ...

More details
5 Emission Control Technologies - US EPA

5 Emission Control Technologies - US EPA

Oxidation (LSFO) — a wet FGD technology — and Lime Spray Dryer (LSD) — a semi-dry FGD technology which employs a spray dryer absorber (SDA). In wet FGD systems, the polluted gas stream is brought into contact with a liquid alkaline sorbent (typically limestone) by forcing it through a pool of the liquid slurry or by spraying it with the ...

More details
Spray Dryer Nozzle for Gas Cooling Lechler US

Spray Dryer Nozzle for Gas Cooling Lechler US

The primary task of spray dryers is the cost-effective, reliable and space-saving disposal of waste water. The resulting liquids are usually neutralized and then injected into the hot and to be cooled gas flow. After the liquid has evaporated, the solid and dry evaporation residues can be separated in the downstream filter.

More details
SNCR NOx reduction system - SEFAKO

SNCR NOx reduction system - SEFAKO

The SNCR system reduces flue gas NOx by injecting a water solution of urea at a low concentration to the grate fired boiler furnace chamber within a temperature range of 900 to 1,080˚C; this reduces the NOx emission levels below 200 mg/m 3n. The urea solution injectors are air spray nozzles that provide good mixing with the flue gas stream.

More details
NOx reduction spray nozzles - IKEUCHI

NOx reduction spray nozzles - IKEUCHI

The use of spray nozzle / injection lance for NOx reduction is common in Pollution control to clean the air. But heat, clogging issues, exterior deterioration can damage the nozzles, requiring additional investment to maintain them. We, at IKEUCHI Group, gathered the knowledge of the damages done to analyze them and offer solutions to ensure a ...

More details
Pollution Controls and Available Monitoring Techniques

Pollution Controls and Available Monitoring Techniques

Topic areas THC and OHAP Adsorbers Thermal Oxidizers Catalytic Oxidizers Condensers Capture Systems PM ESP Fabric Filter Venturi Scrubber Acid Gases Wet scrubbers Dry Injection Mercury NOx Selective Catalytic Reduction NSCR Water Injection Low Nox Burners Other Sulfur in Coal Oil Coatings and Solvents ...

More details
NOx reduction with SCR SNCR and Scrubber methods

NOx reduction with SCR SNCR and Scrubber methods

With the common concern over NOx emissions growing, the global trend is to tighten its emission limits. Valmet provides you with a wide range of applications for NOx emission reduction. The most optimal method is always selected case by case. Read more about out SCR, SNCR and Scrubber solutions.

More details
Related Post

Send Message to Us

48-hour idling test machine before leaving the factory. You can take the materials to the factory test machine. We will customize the solution according to your needs.

Get in Touch

Need more additional information or queries? We are here to help. Please fill in the form below to get in touch.

<script type="text/javascript" src="https://s4.cnzz.com/z_stat.php?id=1281088144&web_id=1281088144"></script>